tools:lasercutters:bigred

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
tools:lasercutters:bigred [2021/05/15 15:35]
blakesamuels [Big Red] update photo
tools:lasercutters:bigred [2021/07/22 21:37] (current)
blakesamuels [Introduction] add controller link
Line 1: Line 1:
 ====== Big Red ====== ====== Big Red ======
  
-Back to [[tools:lasercutters:start|Laser Cutters General Info]]+[[tools:start|Tool Register]] - List of all tools
  
-{{:tools:lasercutters:big_red_photo.jpg?400 |}}+[[tools:lasercutters:start|Laser Cutters General Info]] - Info on all laser cutters.
  
-Our largest and most powerful laser cutter. It's good for large pieces of material, thick material and for cutting quickly. It's suitable for use on wood and acrylic like the other laser cutters. It's not as good at engraving as middle red and little red is better at fine detail work.+{{:tools:lasercutters:big_red_photo.jpg?400|}} 
 + 
 +===== Introduction ===== 
 + 
 +Our largest and most powerful laser cutter. It's good for large pieces of material, thick material and for cutting quickly. It's suitable for use on wood and acrylic like the other laser cutters. It's not as good at engraving as middle red while little red is better at fine detail work.
  
 Key Parameters:  Key Parameters: 
  
-  * Model number: LC1290 +  * Laser cutter model number: LC1290 (http://www.wklaser.com/pro_190.aspx
-  * Link: http://www.wklaser.com/pro_190.aspx+  * Controller model number: [[tools:lasercutters:controller_mpc6515|MPC6515]]
   * Nominal cut area: 1200mm×900mm   * Nominal cut area: 1200mm×900mm
   * Honeycomb area is 1165×862   * Honeycomb area is 1165×862
Line 17: Line 21:
   * Laser tube working current: 25-30mA   * Laser tube working current: 25-30mA
   * Lens: China PVD Znse Lens  20mm / 63.5 (2.5 inch) ([[https://www.cloudraylaser.com/products/china-pvd-znse-focusing-lens-for-co2-laser?variant=43422450184|cloudray]])   * Lens: China PVD Znse Lens  20mm / 63.5 (2.5 inch) ([[https://www.cloudraylaser.com/products/china-pvd-znse-focusing-lens-for-co2-laser?variant=43422450184|cloudray]])
 +
 +Computer:
 +  * Dell 03nvj6 (service tag 1nz282s)
 +  * Intel Core 2 Duo e7500
 +  * DDR3 4gb (2x2)
 +  * AMD Radeon R7 250
  
 ===== Instructions for Operator ===== ===== Instructions for Operator =====
Line 49: Line 59:
 ^ Y Axis Pulse Unit | 0.0048000000 | ^ Y Axis Pulse Unit | 0.0048000000 |
  
 +The controller is MPC6515: {{ :tools:lasercutters:laser_cutter_manual_bigred_mpc6515_20140701113449_50485.pdf |Manual}}
 ===== Laser Speeds ===== ===== Laser Speeds =====
 Cut, engraves and marking speeds are listed here for historical record. Some common and more up-to-date cut speeds will be on the whiteboard next to the laser cutters for common materials. Operators are encouraged to post their cut speeds to `#lasers-big-red` on Slack. Cut, engraves and marking speeds are listed here for historical record. Some common and more up-to-date cut speeds will be on the whiteboard next to the laser cutters for common materials. Operators are encouraged to post their cut speeds to `#lasers-big-red` on Slack.
  • tools/lasercutters/bigred.1621064149.txt.gz
  • Last modified: 2021/05/15 15:35
  • by blakesamuels