tools:lasercutters:bigred

This is an old revision of the document!


Big Red

Back to Laser Cutters

Our largest and most powerful laser cutter. It's good for large pieces of material, thick material and for cutting quickly. It's suitable for use on wood and acrylic like the other laser cutters. It's not as good at engraving as middle red and little red is better at fine detail work.

Key Parameters:

  • Model number: LC1290
  • Nominal cut area: 1200mm×900mm
  • Honeycomb area is 1165×862
  • Laser type: CO2 10.6um laser
  • Current laser tube: SPT-TR130 (130W)
  • Laser tube working current: 25-30mA
  • Lens: China PVD Znse Lens 20mm / 63.5 (2.5 inch) (cloudray)

This is the checklist operators should be working through as they go about their laser cutting jobs.

Click to view larger version (click again for full resolution).

  • 2021-now SPT-TR130 (purchased: aliexpress)
  • 2018–2021 100W CO2 laser tube (donated along with Middle Red)
  • 2017?–2018 Reci 130W W6 CO2 laser tube, max 26mA)

Big red can cut thicker materials due to a longer focal lens than little red. Big red cannot operate the laser tube at low enough power levels to perform very fine engraving. The step size of big red is larger than the other laser cutters as well which means less fine detail in cuts.

To ensure tube longevity and reliability the tube should not be operated above its max working current. This is set by adjusting “laser power percentage” in lasercut software and checking current draw during cutting.

Manual “test” laser fires are currently configured to 10mA, ~40% of the configured Max-Power.

Big Red's cut and engrave speeds are limited to 200mm/s to reduce shaking the mirrors or delicate components out of alignment. Middle red can engrave much faster.

To install the rotary axis for doing round things you need to first disconnect the Y axis and connect the rotary axis.

Note: This page used to be over at lc1290_parameters but was overhauled and moved here. That page title was: “LC1290 Laser Cutting / Engraving Reference”

Machine Settings:

X Axis Pulse Unit 0.0048000000
Y Axis Pulse Unit 0.0048000000

bannedmaterials

Cut, engraves and marking speeds are listed here for historical record. Some common and more up-to-date cut speeds will be on the whiteboard next to the laser cutters for common materials. Operators are encouraged to post their cut speeds to `#lasers-big-red` on Slack.

Please note that these parameters may not be completely accurate, as they assume that the laser is clean, calibrated and aligned. Always test a small cut on your material before committing to a large job (or be prepared to repeat the cut without moving material).

Material Thickness Feedrate Power Preview Result/notes
Ply 3mm 40mm/s 100% Warps just by looking at it. May benefit from *careful* weighting down… *avoid path of laser head!!*
6mm 20mm/s 100%
9mm 10mm/s 100%
12mm 6mm/s 100%
Exterior/Marine Ply 4mm 17-20mm/s 100%
6mm 5mm/s 100%
MDF 3mm 35 mm/s 100%
6mm 20mm/s 100%
9mm 7mm/s 100%
12mm 5mm/s 100%
Acrylic 3mm 25mm/s 100%
6mm
10mm 7mm/s 100%
12mm
LaserMax 1.6mm 200mm/s 50% (still really powerful!)
Corflute 5mm ~40mm/s 100%
Hard Range EVA Tile (Black) 12mm 40mm/s 100% (50% corners) The ones that fit together like a jigsaw. Note that the speed is based on having the hard side at the bottom. Speed can be increased if the hard surface is facing up and faster again if there is no hard side (eg yoga mats)
Pine 19mm 6mm/s 100%
12mm 7mm/s 100%
Corkboard 6mm - - Will not cut completely without severe charring despite very aggressive parameters. Don't bother. Not yet an approved material.
PETG (Polyethylene terephthalate) 0.5mm 120mm 40% (Corner 35%)
Material Scan Gap Feedrate Power Preview Result
MDF 0.075mm 200mm/s 35%
MDF (wide) 0.05mm 350mm/s 25% Weird resonance and skipping over a wide (450mm) area using above settings. This worked better.
MDF (line) na 100 mm/s 25% For line work, as opposed to raster engraving. Make sure corner power is set to the same level.
Coir Doormat (unused) 0.5mm 350mm/s 35% Grey scale images do not work.
Material Thickness Feedrate Power Preview Result
MDF 3mm 200mm/s 25%
  • tools/lasercutters/bigred.1618111010.txt.gz
  • Last modified: 2021/04/11 11:16
  • by blakesamuels