tools:lasercutters:bigred

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
tools:lasercutters:bigred [2021/04/10 20:37]
blakesamuels Moved content from lasercutters:lc1290_parameters
tools:lasercutters:bigred [2021/07/22 21:37] (current)
blakesamuels [Introduction] add controller link
Line 1: Line 1:
 ====== Big Red ====== ====== Big Red ======
  
-Back to [[tools:lasercutters:start|Laser Cutters]]+[[tools:start|Tool Register]] - List of all tools
  
-Our largest and most powerful laser cutter. It's good for large pieces of material, thick material and for cutting quickly. It's suitable for use on wood and acrylic like the other laser cutters. It's not as good at engraving as middle red and little red is better at fine detail work.+[[tools:lasercutters:start|Laser Cutters General Info]] - Info on all laser cutters.
  
-  Model number: LC1290+{{:tools:lasercutters:big_red_photo.jpg?400|}} 
 + 
 +===== Introduction ===== 
 + 
 +Our largest and most powerful laser cutter. It's good for large pieces of material, thick material and for cutting quickly. It's suitable for use on wood and acrylic like the other laser cutters. It's not as good at engraving as middle red while little red is better at fine detail work. 
 + 
 +Key Parameters:  
 + 
 +  Laser cutter model number: LC1290 (http://www.wklaser.com/pro_190.aspx) 
 +  * Controller model number: [[tools:lasercutters:controller_mpc6515|MPC6515]]
   * Nominal cut area: 1200mm×900mm   * Nominal cut area: 1200mm×900mm
   * Honeycomb area is 1165×862   * Honeycomb area is 1165×862
-  * Laser tube power: 130W +  * Laser type: CO2 10.6um laser 
-  * Linkhttp://www.wklaser.com/pro_190.aspx+  * Current laser tube: SPT-TR130 (130W) 
 +  * Laser tube working current25-30mA 
 +  * Lens: China PVD Znse Lens  20mm / 63.5 (2.5 inch) ([[https://www.cloudraylaser.com/products/china-pvd-znse-focusing-lens-for-co2-laser?variant=43422450184|cloudray]])
  
 +Computer:
 +  * Dell 03nvj6 (service tag 1nz282s)
 +  * Intel Core 2 Duo e7500
 +  * DDR3 4gb (2x2)
 +  * AMD Radeon R7 250
  
-====== LC1290 Laser Cutting / Engraving Reference ====== +===== Instructions for Operator =====
-===== Summary ===== +
-{{:lasercutters:bigred.jpg?300 |}}The LC1290 lasercutter is equipped with a [[https://www.aliexpress.com/item/33026988722.html|SPT]] SPT-TR130 CO2 laser tube. To ensure tube longevity and reliability the tube should **not** be operated above 26mA as indicated by the current meter on the machine. Manual "test" laser fires are currently configured to 10mA, ~40% of the configured Max-Power.\\ +
-(Previously: 2018--2020 100W CO2 laser tube)\\ +
-(Previously: 2017?--2018 [[http://www.recilaser.com/en/productInfo/fc9181e93b448cac013b44f8a3e20e65.htm|Reci]] 130W W6 CO2 laser tube, max 26mA)\\ +
-\\ +
-It can cut thicker materials than the LG500 (due to a slightly longer focal lens) and at higher speeds (due to the higher laser power). However, it cannot operate the laser tube at low enough power levels to perform very fine engraving.\\+
  
-Please note that these parameters may not be completely accurate, as they assume that the laser is perfectly calibrated and aligned. In the case that the laser is not perfectly aligned (which is most of the time), power levels will need to be adjusted upwards and/or feed rates lowered accordingly.+This is the checklist operators should be working through as they go about their laser cutting jobs.
  
-**Big Red's cut and engrave speeds are limited to 200mm/s to reduce shaking the mirrors or delicate components out of alignment.**+//Click to view larger version (click again for full resolution).// 
 + 
 +{{:tools:lasercutters:big_red.png?300|}} 
 + 
 +===== Laser Tube History ===== 
 +  2021-now [[https://www.sptlaser.net/co2-laser-tube/tr-series|SPT-TR130]] (purchased: [[https://www.aliexpress.com/item/33026988722.html|aliexpress]]) 
 +  2018--2021 100W CO2 laser tube (donated along with Middle Red) 
 +  * 2017?--2018 [[http://www.recilaser.com/en/productInfo/fc9181e93b448cac013b44f8a3e20e65.htm|Reci]] 130W W6 CO2 laser tube, max 26mA) 
 + 
 +===== General Notes ===== 
 + 
 +Big red can cut thicker materials due to a longer focal lens than little red. Big red cannot operate the laser tube at low enough power levels to perform very fine engraving. The step size of big red is larger than the other laser cutters as well which means less fine detail in cuts. 
 + 
 +To ensure tube longevity and reliability the tube should **not** be operated above its max working current. This is set by adjusting "laser power percentage" in lasercut software and checking current draw during cutting.  
 + 
 +Manual "test" laser fires are currently configured to 10mA, ~40% of the configured Max-Power. 
 + 
 +Big Red's cut and engrave speeds are limited to 200mm/s to reduce shaking the mirrors or delicate components out of alignment. Middle red can engrave much faster. 
 + 
 +To install the rotary axis for doing round things you need to first disconnect the Y axis and connect the rotary axis. 
 + 
 +Note: This page used to be over at [[lasercutters:lc1290_parameters|]] but was overhauled and moved here. That page title was: "LC1290 Laser Cutting / Engraving Reference" 
 + 
 +Machine Settings: 
 +^ X Axis Pulse Unit | 0.0048000000 | 
 +^ Y Axis Pulse Unit | 0.0048000000 | 
 + 
 +The controller is MPC6515: {{ :tools:lasercutters:laser_cutter_manual_bigred_mpc6515_20140701113449_50485.pdf |Manual}} 
 +===== Laser Speeds ===== 
 +Cut, engraves and marking speeds are listed here for historical record. Some common and more up-to-date cut speeds will be on the whiteboard next to the laser cutters for common materials. Operators are encouraged to post their cut speeds to `#lasers-big-red` on Slack. 
 + 
 +==== Cutting ==== 
 +Please note that these parameters may not be completely accurate, as they assume that the laser is clean, calibrated and aligned. Always test a small cut on your material before committing to a large job (or be prepared to repeat the cut without moving material).
  
-[[lasercutters:bannedmaterials]] 
-===== Cutting ===== 
-|< 90% 15% 10% 10% 10% 55% >| 
 ^ Material ^ Thickness ^ Feedrate ^ Power ^ Preview Result/notes ^ ^ Material ^ Thickness ^ Feedrate ^ Power ^ Preview Result/notes ^
 | Ply      | 3mm       | 40mm/  | 100%  | Warps just by looking at it. May benefit from *careful* weighting down... *avoid path of laser head!!* | | Ply      | 3mm       | 40mm/  | 100%  | Warps just by looking at it. May benefit from *careful* weighting down... *avoid path of laser head!!* |
Line 49: Line 88:
 |Corkboard| 6mm | - | - | Will not cut completely without severe charring despite very aggressive parameters. Don't bother. Not yet an approved material. | |Corkboard| 6mm | - | - | Will not cut completely without severe charring despite very aggressive parameters. Don't bother. Not yet an approved material. |
 |PETG (Polyethylene terephthalate)| 0.5mm| 120mm | 40% (Corner 35%) |  |  |PETG (Polyethylene terephthalate)| 0.5mm| 120mm | 40% (Corner 35%) |  | 
-===== Engraving ====+ 
-|< 90% 20% 10% 10% 10% 50% >|+==== Engraving ====
 ^ Material ^ Scan Gap  ^ Feedrate ^ Power ^ Preview Result ^ ^ Material ^ Scan Gap  ^ Feedrate ^ Power ^ Preview Result ^
 | MDF                    | 0.075mm   | 200mm/ | 35%                  | | MDF                    | 0.075mm   | 200mm/ | 35%                  |
Line 57: Line 96:
 | Coir Doormat (unused) | 0.5mm | 350mm/s | 35% | Grey scale images do not work. |  | Coir Doormat (unused) | 0.5mm | 350mm/s | 35% | Grey scale images do not work. | 
  
-===== Low Powered Line Cut ====+==== Low Powered Line Cut ====
-|< 90% 20% 10% 10% 10% 50% >|+
 ^ Material ^ Thickness  ^ Feedrate ^ Power ^ Preview Result ^ ^ Material ^ Thickness  ^ Feedrate ^ Power ^ Preview Result ^
 | MDF                    | 3mm   | 200mm/ | 25%                  | | MDF                    | 3mm   | 200mm/ | 25%                  |
  
- +==== From old Maintenance page ==== 
 +Big Red Consumables.
  
-===== Machine Settings ===== +Lense: 20mm Dia, 50.8mm Focal Length, Currently ZnSe, Potentially worth changing to GAAS lense instead? 
-Please do not edit this bit! These are the standard settings for the machine.\\ + 
-^ X Axis Pulse Unit | 0.0048000000 | +Mirrors: 25mm Dia, 1st and 2nd mirror are Molybdenum, 3rd Mirror is Silicon GoldChange all to Molybdenum? 
-^ Y Axis Pulse Unit | 0.0048000000 | + 
-==== Rotary Axis Installation ==== +Guide to aligning mirrors on Laser
-To install the rotary axis for doing round things you need to first disconnect the Y axis and connect the rotary axis FIXME\\+ 
 +http://justaddsharks.co.uk/support/laser-beam-alignment-guide 
 + 
 +See "[[file://filer/shared/member work/lemming/laser alignment]]" for laser alignment targets. 
 + 
 +==== Documents ==== 
 +  - {{ :tools:lasercutters:hy-z_series_laser_power_supply_user_manual.pdf |HY-Z Laser Power Supply}}
  
  • tools/lasercutters/bigred.1618058246.txt.gz
  • Last modified: 2021/04/10 20:37
  • by blakesamuels